Quantum P3000 Guide de l'utilisateur Page 92
- Page / 146
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 6 Troubleshooting
Common Problems and Solutions
72 Quantum|ATL P3000 Series User’s Guide
Start-up
Problems
6
Table 7
describes corrective actions for problems which occur
during start-up.
Table 7 Start-up
Problems
Problem Corrective Action
The library does not power
on.
Make sure the power cord is connected to a dedicated,
grounded electrical outlet and the power switch behind the
slide panel just below the GUI is on.
The library or tape drives do
not respond on the SCSI bus.
Make sure each SCSI device on the same SCSI bus has a unique
address and the last device is properly terminated.
During initialization, the
library reports “Not Ready.”
Determine the failure type by checking any previous error codes
returned to the host computer. Correct the cause of the error.
One or more tape drives fail
to spin up during start-up.
Check all SCSI cabling and termination behind the center back
access door. If necessary, contact your field service engineer
about replacing the drives.
The library starts up in
standby mode.
Press the Standby button to verify that the library switches to
on-line mode. You can use the GUI to select either on-line or
standby mode at power up.
- User’s Guide 1
- Contents 3
- Ta b l e s 14
- Audience 15
- Customer Support 19
- [email protected] 19
- Library Description 21
- DLT and/or DLT and/or 24
- LTO SDLT 24
- Features and Benefits 25
- Library Components 26
- Front Panel 27
- Cabinet-Back 28
- Quantum 29
- IntelliGrip 30
- Media CHM 30
- Load Port and 32
- Magazines 32
- Basic Library Operations 35
- Installing Tape Cartridges 36
- DLT/SDLT 37
- Cartridges 37
- Labeling 37
- Proper Insertion Orientation 38
- A F L 0 5 3 39
- DLTtape IV 39
- A B C 1 2 3 L 1 40
- Figure 11 Cabling 42
- Configuration 16 Drive 42
- Using the GUI 44
- Figure 12 GUI—Initial 45
- Table 5 GUI 46
- Components 46
- Library Controls 48
- Obtaining Library Status 49
- Activity 51
- Load Port 51
- Tapes Screen 52
- Figure 18 Password 55
- Operating the Load Port 56
- Warning: 58
- Inserting LTO Tape 59
- Unload button 60
- Insert/release 60
- (shown in up position) 60
- Operator Commands 63
- Opening the Operator Screen 64
- Configuring the Library 65
- Press the Configure button 66
- Configuring Library Options 67
- Chapter 3 Operator Commands 68
- Performing an Inventory 69
- Moving Cartridges 70
- Backspace button: 71
- Unloading a Drive 72
- Unloading the Load Port 73
- Service Commands 75
- Opening the Service Screen 76
- Changing Passwords 77
- Generating Reports 78
- Service Report 79
- Statistics Report 79
- Generating Any 79
- Report: Statistics 80
- Operator 80
- Testing the Library 82
- Chapter 4 Service Commands 83
- Figure 36 Test: 83
- Systest Library Screen 83
- Multi-Unit Commands 85
- Opening the Multi-Unit Screen 86
- Figure 38 Multi-Unit 87
- Figure 39 Configure 88
- Multi-Unit 88
- Figure 40 Multi-Unit 89
- Troubleshooting 91
- Chapter 6 Troubleshooting 92
- Common Problems and Solutions 92
- Table 7 Start-up 92
- Problems 92
- Table 10 95
- Table 11 Tape Drive 96
- Figure 41 Tape Drive 98
- Library Specifications 99
- Environmental Specifications 101
- Relocating the Library 105
- Caution: 106
- Horizontal 110
- Crating the Library 114
- Automatic Drive Cleaning 119
- Selection of Cleaning Mode 120
- Reporting of Cleaning Mode 121
- Cleaning Cartridges 122
- Storage and 123
- Tracking 123
- Monitoring 123
- Element Status 124
- Information 124
- Monitoring the Drives 125
- Media Movement to the Drive 125
- Media Movement from the Drive 127
- Unloading Cleaning Cartridges 127
- Laser Regulations 129
- Laser Warning 130
- Exposure Warning 130
- Regulatory Statements 131
- CISPR-22 132
- WARNING! 132
- ACHTUNG! 132
- ATTENTION! 132
- Laser Statement 134
- Battery Statement 135
- ATTENTION 136
- Attenzione 136
- PRECAUCIÓN 136
- VARNING! 136
- Glossary 137
- C Calibrate 138
- Check Condition status 138
- CISPR 22 138
- Class A digital device 138
- Class I laser product 138
Produits connexes et manuels pour Chargeurs automatiques de bandes et bibliothèques Quantum P3000
Chargeurs automatiques de bandes et bibliothèques Quantum Scalar i2000 Guide de l'utilisateur
(77 pages)
(77 pages)
Chargeurs automatiques de bandes et bibliothèques Quantum Scalar i40 Guide de l'utilisateur
(340 pages)
(340 pages)
Chargeurs automatiques de bandes et bibliothèques Quantum Scalar 50 LTO-3HH Guide de l'utilisateur
(290 pages)
(290 pages)
Chargeurs automatiques de bandes et bibliothèques Quantum Scalar i80 Guide de l'utilisateur
(18 pages)
(18 pages)
Chargeurs automatiques de bandes et bibliothèques Quantum Scalar i40 Guide de l'utilisateur
(328 pages)
(328 pages)
Chargeurs automatiques de bandes et bibliothèques Quantum EC-LLDAA-YF-B Guide de l'utilisateur
(210 pages)
(210 pages)
Chargeurs automatiques de bandes et bibliothèques Quantum Scalar 10K Instructions d'exploitation
(324 pages)
(324 pages)
Chargeurs automatiques de bandes et bibliothèques Quantum FastStor 2 Guide de l'utilisateur
(68 pages)
(68 pages)
Chargeurs automatiques de bandes et bibliothèques Quantum DLT 8000 Guide de l'utilisateur
(34 pages)
(34 pages)
Chargeurs automatiques de bandes et bibliothèques Quantum ATL StackLink Guide de l'utilisateur
(222 pages)
(222 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels