Quantum Scalar 100 Guide de l'utilisateur Page 71
- Page / 126
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring your Library 8-61
Scalar 100
2. Select Enable or Disable to check or uncheck the box.
A checked box indicates AutoClean is enabled.
3. Select OK.
Setting Drive SCSI IDs
Use Drive to set drive SCSI IDs. The drive SCSI IDs must be different from other SCSI devices on
the SCSI bus. Available SCSI IDs are 0 to 15.
Path: Main menu > More > Setup > Drive > SCSI
To set a drive SCSI ID
1. From the Main menu, select More. Select Setup and then select Drive. Select SCSI.
2. Use Change Drive to select the drive whose SCSI ID you want to set.
3. Select Next.
4. Use Up and Down to pick the new SCSI ID for that drive.
The CURRENT column displays the current SCSI ID. The NEW column displays the new SCSI
ID.
5. Select Next.
6. After the dialog refreshes, the Drives with this ID shows how many other drives use the
selected SCSI ID. If it displays NONE, select OK. Otherwise, change the drive SCSI ID so that
it is unique.
The library resets the SCSI IDs of the affected drives.
7. When complete, select OK.
Setting the Date and Time
Use Date/Time to set the library date and time used by the library logs and displayed on the
Operator Panel.
Note that this does not affect the date and time used by the Remote Management Unit (RMU), but
does affect the date and time shown in the logs retrieved by the RMU.
Path: Main menu > More > Setup > Utils > Date/Time
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Produits connexes et manuels pour Chargeurs automatiques de bandes et bibliothèques Quantum Scalar 100
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels