Quantum DLT-V4 Manuel d'utilisateur télécharger pdf (Page 34)

Chapter 3 Installing the Internal SATA Tape Drive

Installing the Internal SATA Tape Drive

DLT-V4 Product Manual 18

Installing the Internal SATA Tape Drive 3

To install the tape drive, follow these steps:

1 Shut down the operating system and power off the server or

workstation.

2 Power off all peripheral devices, such as printers and other connected

devices.

3 Remove the cover from the server or workstation as described in the

server or workstation’s documentation (see figure 8

Figure 8 Removing the

Workstation Cover (example)

Caution:

Do not go to step 3 until you have completed steps 1

and 2. Failure to follow these instructions may result

in damage to the tape drive or other devices.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 96 97

'/79 1
Contents 3
DLT-V4 Product Manual iv 4
DLT-V4 Product Manual v 5
Chapter 10 Specifications 64 6
Glossary 76 6
DLT-V4 Product Manual vii 7
DLT-V4 Product Manual viii 8
DLT-V4 Product Manual ix 9
DLT-V4 Product Manual x 10
DLT-V4 Product Manual xi 11
DLT-V4 Product Manual xii 12
DLT-V4 Product Manual xiii 13
DLT-V4 Product Manual xiv 14
DLT-V4 Product Manual xv 15
Global Services 0 16
Introduction 17
Features 1 18
Installing the Internal 20
SCSI Tape Drive 20
Installation Steps 2 21
Setting the SCSI ID 2 22
Drive power connector 23
SCSI ID jumper block 23
68-pin high-density 23
SCSI connector 23
Figure 3 25
Terminator 26
SCSI cable 26
(supplied with 26
2U enclosure 28
Confirming the Installation 2 31
SATA Tape Drive 32
Installation Steps 3 33
Confirming the Installation 3 38
SATA-to-USB Tape Drive 39
USB Requirements 4 40
Installation Steps 4 40
Installation 46
Confirming the Installation 4 48
Installing the Tabletop 49
Installation Steps 5 50
DLT-V4 Product Manual 35 51
DLT-V4 Product Manual 36 52
Setting the SCSI ID 5 53
Press here to decrease 54
Press here to increase 54
SCSI host 56
Confirming the Installation 5 58
USB/eSATA Tape Drive 59
Installation Steps 6 60
DLT-V4 Product Manual 45 61
Confirming the Installation 6 63
Installing the Device 64
Microsoft Windows 2000 7 65
Using Your Tape Drive 67
Unload Button Functions 8 70
Unload Button Actions 8 71
Diagnostic Mode Event Codes 8 72
Diagnostic Mode Event Codes 73
DLT-V4 Product Manual 57 73
Table 11 Diagnostic Mode 73
Event Codes 73
Using Data and 74
Cleaning Cartridges 74
Loading a Data Cartridge 9 75
Unloading a Data Cartridge 9 76
Write-protect 77
Write protected 77
Write enabled 77
Indicator 77
Specifications 80
Dimensions and Weights 10 81
Functional Specifications 10 83
Timing Characteristics 10 84
Reliability Factors 10 85
Regulatory and 86
Compliance Information 86
Safety Requirements 11 87
Consumer Bulletin Scheme 11 87
(Tabletop Tape Drive) 11 88
DLT-V4 Product Manual 73 89
DLT-V4 Product Manual 74 90
Environmental Compliance 11 91
Glossary 92

Commentaires sur ces manuels

Pas de commentaire

Quantum DLT-V4 Manuel d'utilisateur Page 34

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de bandes magnétiques Quantum DLT-V4