Quantum 1200 Series DAT Autochanger Guide de l'utilisateur Page 140
- Page / 294
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MODE SELECT (6) / (10) Command (15h / 55h) SDLT 600 SCSI Interface Guide
4-98 January 2005 81-81200-02 REV A01
4.9.13 EEPROM Vendor Specific Page (3Eh)
The drive supports an EEPROM Vendor Specific Page that enables an initiator to modify savable
parameters. Only one savable parameter can be changed per MODE SELECT command.
Figure 4-56. EEPROM Vendor Specific MODE SELECT Page — Data Format
The ASCII string has a parameter name followed by one or more space characters, a parameter value,
and an ASCII line feed or null character. When the string is parsed, the parameter value is interpreted
as shown in the following table. Note that the parameter name may be in upper or lower case. The
drive saves the savable parameters during resets and power cycles.
Bit
Byte
7 6 5 4 3 2 1 0
0 PS Rsv’d Page Code (3Eh)
1 Page Length
2 - n ASCII String of Parameter Name and Value
Table 4-58. EEPROM Vendor Specific MODE SELECT Page — Parameter Descriptions
Parameter Name
Data
Type
Default
Length
(Bytes)
Usage
VendorID ASCII QUANTUM 8 Vendor Identification field in
INQUIRY data.
ProductID ASCII SDLT600 16 Product Identification field in
INQUIRY data. SDLT600 for the
SDLT 600 tape drive.
BTHDirMode Decimal 2 1 Obsolete.
CacheTMs Binary 0 1 When set, the drive always treats a
WRITE FILEMARKS command
that writes a single filemark and is
not preceded by another WRITE
FILEMARKS command as if the
Immed bit was set to 1.
DefaultCompON Binary 1 1 When set to 0, indicates that
compression is defaulted OFF at
power-on/reset.
When set to 1, indicates that
compression is defaulted ON at
power-on/reset.
DefFixedBlkLen Decimal 0 4 Default fixed block size.
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Produits connexes et manuels pour Logiciel Quantum 1200 Series DAT Autochanger
(160 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels